Less than a month separated two World Championship victories for Canyon which, viewed from the front, appeared to offer very different answers to the same broad aerodynamic question.

At the Road World Championships, Marlen Reusser won the elite women's time trial on Canyon's unreleased Speedmax CFR TT, with Zoe Backstedt second on another example of the same bike. Its most obvious change was the front end. The fork had moved substantially away from the wheel into a double-crown arrangement, and Canyon's explanation was more significant than the appearance: during development, increasing that separation continued to improve the complete rider-bike system. Development lead Lukas Schuchnigg said the original concept went wider again before Canyon had to bring it inside the UCI limit, while the company claims the finished machine saves at least five watts over its predecessor and as much as eight watts depending on the rider. Canyon says the bike was optimised around 50 km/h and that the upper fork sections help manage the airflow approaching the rider's legs.

Schuchnigg also led development of Canyon's Speedmax CFR Track. When that bike appeared in 2023, Canyon had reached almost the opposite conclusion. Rather than following Britain and Australia towards increasingly wide front structures, it used an unusually narrow fork built around a 40 mm front axle. Schuchnigg said Canyon "couldn't see the reason" for the wide stance used by Hope, adding that its testing showed a narrower solution could provide the aerodynamic performance it wanted while also being stiffer.

Three years later, the same development lead had produced a road TT bike on which moving the fork outwards continued to improve the measured system until the regulations became the boundary. Reusser's machine immediately raised the possibility that some of that development might eventually appear on Canyon's LA28 track bike.

Shanghai gave Canyon a very good reason to test that assumption rather than simply follow it.

Canyon changed its mind, but its old answer is still fast

Denmark won the men's team pursuit for the fourth consecutive World Championships in Shanghai, with Carl-Frederik Bevort, Lasse Leth, Frederik Madsen and Rasmus Pedersen recording 3:40.865 in the final. That was less than a second outside Denmark's 3:39.977 world record from Konya, and it came on essentially the same narrow-fronted Canyon architecture introduced in 2023.

The performance does not prove that Canyon's narrow fork is aerodynamically superior to a wider alternative. A team-pursuit result cannot isolate one frame variable from rider power, position, pacing, tyres, drivetrain, wheels, environmental conditions and everything else contributing to the system. It does establish that Canyon's 2023 solution has not become a performance dead end while its road engineers have been moving in the opposite direction.

The two Canyon projects are not solving identical problems. The new Speedmax TT was developed around approximately 50 km/h, with a road time-trial wheel configuration, outdoor aerodynamic conditions and a different rider position. A pursuit bike operates at substantially higher speeds, normally with a front disc, in an indoor environment with very low yaw and with a position developed around the particular demands of track racing. Team pursuit then adds the further complication that most of the race is not ridden in clean air.

There is no reason those different boundary conditions have to produce the same optimum fork spacing.

If Canyon's eventual LA28 machine moves significantly wider, it will have done so after testing against a narrow concept which has just won another World Championship at 3:40.865. If it remains narrow, that would be equally revealing: whatever Canyon has learnt from the new TT bike does not transfer strongly enough to the track to displace an architecture that is already working exceptionally well.

Jonathan Milan then provided another reminder that the narrow approach is very much alive.

He qualified for the individual-pursuit final in 3:58.850, becoming the first rider below 3:59 and setting a new world record at 60.289 km/h. Filippo Ganna later took bronze, while Milan, Ganna, Francesco Lamon and Alessio Magagnotti had already taken silver behind Denmark in the team pursuit.

Milan's Pinarello Bolide F HR follows a philosophy that was deliberately developed around reducing frontal area. The original Hour Record machine narrowed the bottom bracket to 54 mm, the rear hub to 89 mm and the front hub to 69 mm. Pinarello subsequently carried that design language into Italy's endurance programme rather than treating it as a one-off solution for Ganna.

That direction was not developed without exposure to the same system-level aerodynamic thinking that had influenced British track development. Dan Bigham rode the prototype before Ganna's Hour Record and later described the frame, wheels and much of the equipment on Ganna's record bike as effectively the same as his own, characterising the project as "all super narrow". Pinarello itself has said that its work on wide forks and stays had not produced sufficiently conclusive results to justify abandoning the narrow approach.

Shanghai therefore produced two of the strongest men's endurance performances of the championships on deliberately narrow front ends without establishing that narrowness caused either of them.

Britain's women provide the corresponding warning against drawing the opposite conclusion. Great Britain won the women's team pursuit in 4:04.610 while remaining within the wide-frame philosophy developed through the Hope-Lotus programme. Australia qualified fourth in the men's event in 3:48.797 on the Factor HANZO before losing to Denmark in the first round.

Those performances tell us which combinations of riders and equipment were fastest in Shanghai. They do not provide an A/B test of fork width.

They do show that neither design direction has become obsolete just as the UCI prepares to reduce the space available to pursue both.

What survives after 7 September 2027?

From 7 September 2027, UCI rule 1.3.017 sets the maximum distance between the inside faces of the two front-fork legs at 115 mm and the corresponding rear-triangle distance at 145 mm. The amendment also removes the separate track wording which had applied those measurements only at the lower extremity of the fork and rear extremity of the triangle, bringing track equipment under the general restriction instead.

That effectively ends the most extreme interpretation of the Hope-Lotus idea.

The original British machine made its thinking unusually visible because the fork and rear structures moved far enough outboard to occupy some of the same broad frontal region as the rider's legs. The aerodynamic question was no longer how little drag the bare bicycle created, but what happened when frame, wheels and athlete were treated as one system.

The new measurements still allow considerably more separation than Canyon currently uses, but they remove much of the freedom to position structural members around the rider in the manner that defined the Tokyo and Paris bikes.

Factor's response has not been to abandon the HANZO. A replacement fork is being developed so that existing frames can be brought inside the September 2027 requirements rather than consigning the entire architecture to the previous Olympic cycle. Factor's description of the original bike says the wide fork was developed around the interaction between the rider, frame and wheels, including the airflow around the moving legs and through the space between bicycle and athlete.

Changing the fork rather than replacing the whole concept does not tell us how much of the original aerodynamic effect survives inside 115 mm. It does suggest that Factor believes there is enough worth retaining to continue developing it.

Hope has also shown that the HB.T architecture can be made compliant, with a version now offered using the 2027-legal HFK04 fork. That should not, however, be confused with confirmation that this will be Great Britain's LA28 frame.

There are already reasons to doubt that assumption. The current 2027-compliant HB.T frameset is priced at around GBP15,000, well above the EUR12,500 excluding VAT frameset price cap introduced within the UCI's LA28 equipment changes. More importantly, an existing frame adapted to remain legal through 2027 is not necessarily the same thing as a national programme's final answer for an Olympic Games still almost two years beyond the rule change.

For the moment, the Hope bike tells us that the wide architecture can survive the dimensional restriction. What Britain ultimately chooses for LA28 remains a different question.

The aerodynamic reasoning becomes harder to see once the structures can no longer extend so far towards the rider.

It would be easy to reduce the old wide-fork argument to a fork hiding the rider's legs. That certainly helped make the Hope solution visually understandable, but the public explanations from Factor and Canyon point to a broader interaction involving the wheel, the fork and the condition of the flow arriving further downstream.

Canyon's new TT fork does not sit directly in front of Reusser's legs in anything approaching the way the original Hope structures did, yet Canyon says the complete system continued to improve as the fork moved outward. Factor has described its track development in similarly system-level terms rather than presenting the fork simply as a shield in front of the rider.

There is not enough public data to separate the contribution of wheel-fork interaction, the flow through the space between the structures, the wake arriving at the rider or other effects. Assigning wattage to any of those mechanisms from outside the development programmes would be guesswork.

The important point is that the extreme rider alignment used by Hope was not necessarily the only reason width could have value. Reducing that alignment does not automatically remove every other interaction that caused programmes to move their forks away from the wheel in the first place.

Neither does the cost of width disappear.

A wider structure still has to justify its frontal area, stiffness, weight and interaction with the rest of the system. Pinarello arrived at the other side of that compromise, and its own development material is clear that wide forks and stays did not produce sufficiently convincing results for it to abandon a narrow solution.

The 115 mm maximum should therefore not be treated as a target.

One programme may use almost all of it because its measured system gain outweighs the consequences of the additional structure. Another may voluntarily leave a significant proportion unused because its combination of wheel, frame, position and rider tests faster that way.

The regulations reduce the available design space without deciding where the optimum lies inside it.

Nor does the optimum have to be identical for every athlete. Ganna and Milan do not present the same body shape, position or leg movement to the air even when riding frames derived from the same design philosophy. Denmark's pursuit setup introduces another set of constraints, as would a smaller female endurance rider.

If the regulations remove some of the huge structural changes available during the previous Olympic cycles, those smaller rider-specific interactions may account for a larger share of what remains.

The bikes could consequently become closer in their maximum dimensions while becoming more deliberate in how differently they use them.

The LA28 question

The same restriction may increase the value of manufacturing freedom.

Pinarello has already demonstrated how differently the same broad aerodynamic philosophy can be manufactured. The Bolide F HR project has included 3D-printed Scalmalloy construction, while Milan's 3:58.850 world record in Shanghai was ridden on the carbon version of the Bolide F HR.

The narrow Pinarello concept does not depend on the frame being printed in metal, just as the use of additive manufacture does not require an entire bicycle to abandon carbon.

The more likely LA28 development is that programmes increasingly choose the manufacturing process according to the part they are trying to produce.

Carbon remains particularly well suited to long aerodynamic structures, low mass and directional stiffness. Additive manufacture offers something different where extremely small production volumes, complex junctions, rider-specific geometry or repeated iterations make conventional mould tooling restrictive.

As the UCI removes some of the large dimensional freedoms that defined the previous Olympic cycle, those manufacturing choices could become more valuable. A fork crown, cockpit, junction or rider-specific component may benefit from being printed even when most of the bicycle remains carbon. Another programme may conclude that additive manufacture allows enough freedom to justify taking the process further into the main frame.

Pinarello may already offer the more useful clue. The same narrow aerodynamic philosophy has now been realised in both printed Scalmalloy and carbon rather than depending on either material. LA28 may therefore be less about finding a replacement for carbon than choosing whichever manufacturing process gives each part of the bicycle the freedom its increasingly restricted geometry demands.

Before Shanghai, Reusser's new TT bike looked like a fairly obvious pointer towards a wider Canyon track machine. Canyon had moved from explicitly questioning wide track forks in 2023 to developing a road TT bike where greater separation continued to produce gains until the UCI limit intervened.

Shanghai made Canyon's eventual decision more revealing.

Its narrow-fronted Speedmax CFR Track has just won a fourth consecutive men's team-pursuit world title. Its new TT bike has moved in the opposite direction because Canyon says the complete road system became faster as the fork moved outward. Those results came from different aerodynamic problems, and the next Canyon track project will tell us how much of the road development survives when a front disc, higher speeds, a pursuit position and the peculiarities of track racing are introduced.

A wider LA28 Canyon would mean the lessons from the TT programme had survived that testing strongly enough to displace an architecture which is already exceptionally successful. Another narrow Canyon would suggest that the apparent contradiction was never really a contradiction: road and track simply demanded different answers.

Factor and Hope will be making their own versions of that decision while working out which parts of the wide-frame era remain useful inside the new rules. Pinarello already presents the counterargument from the other end of the scale, backed by a narrow design lineage which has just produced an individual-pursuit world record. None of those programmes needs to be wrong for their bikes to look very different.

The regulations taking effect on 7 September 2027 will ensure that all of them work inside a smaller box. They will not ensure that the engineers agree on where the bicycle should sit within it.

The interesting measurement heading towards LA28 will not be the maximum width the UCI permits.

It will be how much of it each programme decides is actually worth having.